Видео

Great tip to find center of balance! Subscribed!

Are you using a spiral blade that cuts in all directions? Thanks!

Terrific. Very cool, thanks for sharing. Greetings from a toy maker from Colombia.

Needing your help with the design

I do like this saw. I have a couple issues with it though. The biggest so far was with the bevel adjustment mechanism. The part back by where it tightens has a screw where the rod goes in. The screw sheared off. It wasn't hard to get out and replace, but keep in mind not to over torque the mechanism and over time may become weak. I replaced mine with a harder screw. The other issue is the laser seems really weak. I really don't depend on it, but since it's a feature, I was hoping it would work better than it does. I put a WEN 100 tooth blade on mine. The saw actually is pretty quiet in general for wood cutting tool to me. It does a fantastic job in the overall performance of what it was designed to do.

Muy linda tu artesanía. Que Nuestro SEÑOR JESUCRISTO DIOS PADRE CELESTIAL y ESPÍRITU SANTO; Té dé mucha Salud, Éxitos y muchas Bendiciones.

Consider using a piece of "white board" for the table top instead of plywood. It slides easily, I use it on my bandsaw.

That was very helpful. Thanks

The blade looks very thin gauge. Flimsy. Looks like it worked OK. Why the offset point? What does that do? Is it better than a center point?

Love this! Thank you!!!

Hi from London England, fantastic video, I'm gonna make one! Cheers Rick, all the best mate.

dead links

Thanks for that! Luv it!

Cool!😃

Thank you! Great help.

My dad used to make them for us when were kids,he’d make me a footballer,was a joy to watch him in his little workshop,thanks for sharing this brung back memories 👌

No learning😡😡

I bought plans from woodprix and I made it very fast.

Very good Job !!! Have you got plans ??

😊😅когда кончатся эти бормотания на не пон😊я😊тном языке? Безобразие!

Nice.

Could you give me the dimensions? What is the 2x4?Thanks!🖐

I just purchased that saw. I was puzzled myself with those black hooks. Then I figured it out. Those hooks is to be mounted on right side of saw for power cord. One screw is for front ( meta )l & the other is for the rear end ( plastic ).

Very nice and functional. But in my mind, not that I’ve tried to make a spoon yet, I’m not understanding why the shave horse wouldn’t work for spoons as well.

This is one of the better videos on whirligig ideas. good job!

Did you ever do more with this idea?

Incredible hand steadiness, its needed for delicacy 😊 love the pattern

Great project 👍

How long do we have to leave the water inside?

Hello, did you only add water? Or what exactly did you use?

Now if I only had a lathe….can I stop by when I’m visiting Massachusetts? That would be pissah!

Отличная работа! Большое спасибо за видео!

Thank you

Its not a sloyd... The sloyd is 106.

Thank you again

Thank you

Very well explained lovely to watch 😊

Thank you I will not throw them out anymore great tip

Good video however your sleeves dangling beside the spinning work piece was distracting. I wonder if the taper dimensions could have determined by first measuring the thickness of the metal at the top of the socket and then subtracting twice that amount from the diameter of the taper at the bottom? Obviously if you measure right at the bottom of the socket the wall thickness is greater but I’d bet it’s uniform most of the way down.

Thanks Bro. keep it up

brilliant your so talented

Just what I am looking for. I was about to throw out yet another glue stick. Thank you.

Warm water or cold one?

I don't know what you mean by patton

I like.... In particular the use of hinges is very practical 👍👍

I like the idea

Thanks for this! I made one following your design. Love your common man approach to whipping something together!

And thank you from me because I’ve just turned mine on to find the black pixelation much to my surprise and was panicking that it was broken. But you’ve shown me it’s fine ! You’ve saved me making an embarrassing complaint …of course if the seller has included some info of any kind it would have helped but no….🤦🏽‍♀️..

El anterior acabo en tres patadas y ahora en ingles. Apague y vamos.

Does this also work for brand new sticks that came stuck where the stick does not rise out as you twist upwards?